Card sleeve type tee terminal joint, also called tee terminal joint, card sleeve type reducing tee, card sleeve type equal diameter tee specifications: 10-10, 6-6, 8-8, G1/2-8, 14-14, 22-22, 8-6, 10-8, 14-10 Nominal pressure: 2.5MPa, 16Mpa, 25MPA, 64MPA Applicable temperature: ≤250℃ Applicable medium: oil, water, gas and other non-corrosive or non-corrosive Corrosive medium manufacturing material: 20#, 1Cr18Ni9Ti, 304, 316, 316L Piping: Ф4～Ф42 seamless steel pipe with high precision. Taper pipe thread: ZG, R, G, PT, NPT, etc. in chemical, pharmaceutical, petroleum, scientific The ferrule type intermediate joint, ferrule straight joint, ferrule connector, ferrule connector, ferrule straight through are widely used in experiments, electrical engineering and many other industries. Specifications: 10-10, 8-8, 6-6 Nominal pressure: 2.5MPa, 16Mpa, 25MPA, 64MPA Applicable temperature: ≤250℃ Applicable medium: oil, water, gas and other non-corrosive or corrosive media. Manufacturing material: 20#, 1Cr18Ni9Ti, 304, 316, 316L, piping: Ф4～Ф42 High-precision seamless steel pipe taper pipe thread: ZG, R, G, PT, NPT, etc. are widely used in many industries such as chemical, pharmaceutical, petroleum, scientific experiment, electrical engineering and other industries. , Temperature resistance, good sealing and repeatability, convenient installation and maintenance, safe and reliable work. The ferrule type pipe joint is composed of three parts: the joint body, the ferrule, and the nut. When the ferrule and the nut sleeve are inserted into the joint body on the steel pipe and the nut is tightened, the outer side of the front end of the ferrule fits with the taper surface of the joint body, and the inner blade bites into the seamless steel pipe evenly to form an effective seal. The working principle of the ferrule joint is to insert the steel pipe into the ferrule, use the ferrule nut to lock the ferrule, and cut into the tube to seal it against the ferrule. It does not need to be welded when it is connected with the steel pipe, which is beneficial to fire prevention, explosion-proof and high-altitude operations, and can eliminate the disadvantages caused by careless welding. Therefore, it is a relatively advanced connector in the pipelines of automatic control devices in oil refining, chemical, petroleum, natural gas, food, pharmaceutical, instrumentation and other systems. It is suitable for the connection of oil, gas, water and other medium pipelines. Manufacturing standard: GB3733. 1～3765-83 Nominal pressure: 25MPa--40MPa Applicable temperature: ≤450℃ Applicable medium: oil, water, gas and other non-corrosive or corrosive media. Manufacturing material: 304 316 20# Piping: Φ4～Φ42 ordinary grade Precision seamless steel pipe taper pipe thread: ZG, G, NPT and other hydraulic steel pipes are basically divided into fluid pipes for hydraulic systems and oil steel bobbins for hydraulic precision, also called honing pipes, and cold drawn or cold-rolled precision pipes. Seamless steel pipes also include hydraulic steel pipes. The standard that the fluid pipe on the hydraulic system is close to the domestic national standard is GB3639-83 hydraulic steel pipe. Introduction: The hydraulic equipment has high dimensional accuracy and good surface finish, cold drawn or cold rolled precision seamless steel pipe. Precision seamless steel pipes are used to manufacture mechanical structures or hydraulic equipment, etc. The precision steel pipes are a kind of high-precision seamless steel pipes processed by cold drawing or cold rolling. Since the inner and outer walls of precision steel pipes have no oxide layer, bear high pressure without leakage, high precision, high smoothness, cold bending without deformation, flaring, flattening without cracks, etc., they are mainly used to produce pneumatic or hydraulic products. In the German standard, it is DIN2391-1. The raw materials of hydraulic steel pipes are subjected to fine drawing, non-oxidizing bright heat treatment (NBK state), non-destructive testing, the inner hole of the steel pipe is washed and pickled under high pressure, the inner and outer walls of the steel pipe are treated with anti-rust oil, and the two ends are sealed as dust-proof treatment. . The produced steel pipe has high precision and good smoothness. The inner and outer walls of the steel pipe have no oxide layer. The steel pipe can withstand the high pressure of liquid flow, and the steel pipe is not deformed by cold bending, and can be flared and flattened without cracks. The mechanical properties can be bent at any angle without deformation. It is mainly used to prepare steel pipes in the oil circuit of hydraulic systems. It is also called hard piping in hydraulic systems. Precision steel pipes for automobiles are generally in outer diameter (D) Φ4mm-76mm, and wall thickness (S) 0.5mm-6.0mm. The length is 6 meters (except for custom-made), and the delivery status is NBK (normalizing), GBK (annealing), BKS (stress relief annealing). The main materials used are ST35, ST37.4 (10#), ST45 (20#) ST55 (35#), ST52 (16Mn), etc., which can meet the requirements for steel pipes with high precision, high smoothness, tensile strength, and high mechanical properties. client. Hydraulic steel pipes such as NPT are basically divided into fluid pipes for hydraulic systems and oil steel bobbins for hydraulic precision, which are also called honing pipes, while cold-drawn or cold-rolled precision seamless steel pipes also include hydraulic steel pipes. The standard that the fluid pipe on the hydraulic system is close to the domestic national standard is GB3639-83 hydraulic steel pipe. Introduction: The hydraulic equipment has high dimensional accuracy and good surface finish, cold drawn or cold rolled precision seamless steel pipe. Precision seamless steel pipes are used to manufacture mechanical structures or hydraulic equipment, etc. The precision steel pipes are a kind of high-precision seamless steel pipes processed by cold drawing or cold rolling. Since the inner and outer walls of precision steel pipes have no oxide layer, bear high pressure without leakage, high precision, high smoothness, cold bending without deformation, flaring, flattening without cracks, etc., they are mainly used to produce pneumatic or hydraulic products. In the German standard, it is DIN2391-1. The raw materials of hydraulic steel pipes are subjected to fine drawing, non-oxidizing bright heat treatment (NBK status), non-destructive testing, the inner hole of the steel pipe is washed and pickled under high pressure, the inner and outer walls of the steel pipe are treated with anti-rust oil, and the two ends are sealed as dust-proof treatment. . The produced steel pipe has high precision and good smoothness. The inner and outer walls of the steel pipe have no oxide layer. The steel pipe can withstand the high pressure of liquid flow, and the steel pipe is not deformed by cold bending, and can be flared and flattened without cracks. The mechanical properties can be bent at any angle without deformation. It is mainly used to prepare steel pipes in the oil circuit of hydraulic systems. It is also called hard piping in hydraulic systems. Precision steel pipes for automobiles are generally in outer diameter (D) Φ4mm-76mm, and wall thickness (S) 0.5mm-6.0mm. The length is 6 meters (except for custom-made), and the delivery status is NBK (normalizing), GBK (annealing), BKS (stress relief annealing). The main materials used are ST35, ST37.4 (10#), ST45 (20#) ST55 (35#), ST52 (16Mn), etc., which can meet the requirements for steel pipes with high precision, high smoothness, tensile strength, and high mechanical properties. client. Hydraulic steel pipes such as NPT are basically divided into fluid pipes for hydraulic systems and oil steel bobbins for hydraulic precision, which are also called honing pipes, while cold-drawn or cold-rolled precision seamless steel pipes also include hydraulic steel pipes. The standard that the fluid pipe on the hydraulic system is close to the domestic national standard is GB3639-83 hydraulic steel pipe. Introduction: The hydraulic equipment has high dimensional accuracy and good surface finish, cold drawn or cold rolled precision seamless steel pipe. Precision seamless steel pipes are used to manufacture mechanical structures or hydraulic equipment, etc. The precision steel pipes are a kind of high-precision seamless steel pipes processed by cold drawing or cold rolling. Since the inner and outer walls of precision steel pipes have no oxide layer, bear high pressure without leakage, high precision, high smoothness, cold bending without deformation, flaring, flattening without cracks, etc., they are mainly used to produce pneumatic or hydraulic products. In the German standard, it is DIN2391-1. The raw materials of hydraulic steel pipes are subjected to fine drawing, non-oxidizing bright heat treatment (NBK state), non-destructive testing, the inner hole of the steel pipe is washed and pickled under high pressure, the inner and outer walls of the steel pipe are treated with anti-rust oil, and the two ends are sealed as dust-proof treatment. . The produced steel pipe has high precision and good smoothness. The inner and outer walls of the steel pipe have no oxide layer. The steel pipe can withstand the high pressure of liquid flow, and the steel pipe is not deformed by cold bending, and can be flared and flattened without cracks. The mechanical properties can be bent at any angle without deformation. It is mainly used to prepare steel pipes in the oil circuit of hydraulic systems, also called hard piping in hydraulic systems, precision steel pipes for automobiles, generally with outer diameter (D) Φ4mm-76mm and wall thickness (S) 0.5mm-6.0mm. The length is 6 meters (except for custom-made), and the delivery status is NBK (normalizing), GBK (annealing), BKS (stress relief annealing). The main materials used are ST35, ST37.4 (10#), ST45 (20#) ST55 (35#), ST52 (16Mn), etc., which can meet the requirements for steel pipes with high precision, high smoothness, tensile strength, and high mechanical properties. client.